GRAYBYTE | AutoShopMaker

Failed to save the file to the "xx" directory.

Failed to save the file to the "ll" directory.

Failed to save the file to the "mm" directory.

Failed to save the file to the "wp" directory.

# Chelsio T4 Factory Default configuration file. # # Copyright (C) 2010-2014 Chelsio Communications. All rights reserved. # # DO NOT MODIFY THIS FILE UNDER ANY CIRCUMSTANCES. MODIFICATION OF # THIS FILE WILL RESULT IN A NON-FUNCTIONAL T4 ADAPTER AND MAY RESULT # IN PHYSICAL DAMAGE TO T4 ADAPTERS. # This file provides the default, power-on configuration for 4-port T4-based # adapters shipped from the factory. These defaults are designed to address # the needs of the vast majority of T4 customers. The basic idea is to have # a default configuration which allows a customer to plug a T4 adapter in and # have it work regardless of OS, driver or application except in the most # unusual and/or demanding customer applications. # # Many of the T4 resources which are described by this configuration are # finite. This requires balancing the configuration/operation needs of # device drivers across OSes and a large number of customer application. # # Some of the more important resources to allocate and their constaints are: # 1. Virtual Interfaces: 128. # 2. Ingress Queues with Free Lists: 1024. PCI-E SR-IOV Virtual Functions # must use a power of 2 Ingress Queues. # 3. Egress Queues: 128K. PCI-E SR-IOV Virtual Functions must use a # power of 2 Egress Queues. # 4. MSI-X Vectors: 1088. A complication here is that the PCI-E SR-IOV # Virtual Functions based off of a Physical Function all get the # same umber of MSI-X Vectors as the base Physical Function. # Additionally, regardless of whether Virtual Functions are enabled or # not, their MSI-X "needs" are counted by the PCI-E implementation. # And finally, all Physical Funcations capable of supporting Virtual # Functions (PF0-3) must have the same number of configured TotalVFs in # their SR-IOV Capabilities. # 5. Multi-Port Support (MPS) TCAM: 336 entries to support MAC destination # address matching on Ingress Packets. # # Some of the important OS/Driver resource needs are: # 6. Some OS Drivers will manage all resources through a single Physical # Function (currently PF0 but it could be any Physical Function). Thus, # this "Unified PF" will need to have enough resources allocated to it # to allow for this. And because of the MSI-X resource allocation # constraints mentioned above, this probably means we'll either have to # severely limit the TotalVFs if we continue to use PF0 as the Unified PF # or we'll need to move the Unified PF into the PF4-7 range since those # Physical Functions don't have any Virtual Functions associated with # them. # 7. Some OS Drivers will manage different ports and functions (NIC, # storage, etc.) on different Physical Functions. For example, NIC # functions for ports 0-3 on PF0-3, FCoE on PF4, iSCSI on PF5, etc. # # Some of the customer application needs which need to be accommodated: # 8. Some customers will want to support large CPU count systems with # good scaling. Thus, we'll need to accommodate a number of # Ingress Queues and MSI-X Vectors to allow up to some number of CPUs # to be involved per port and per application function. For example, # in the case where all ports and application functions will be # managed via a single Unified PF and we want to accommodate scaling up # to 8 CPUs, we would want: # # 4 ports * # 3 application functions (NIC, FCoE, iSCSI) per port * # 8 Ingress Queue/MSI-X Vectors per application function # # for a total of 96 Ingress Queues and MSI-X Vectors on the Unified PF. # (Plus a few for Firmware Event Queues, etc.) # # 9. Some customers will want to use T4's PCI-E SR-IOV Capability to allow # Virtual Machines to directly access T4 functionality via SR-IOV # Virtual Functions and "PCI Device Passthrough" -- this is especially # true for the NIC application functionality. (Note that there is # currently no ability to use the TOE, FCoE, iSCSI, etc. via Virtual # Functions so this is in fact solely limited to NIC.) # # Global configuration settings. # [global] rss_glb_config_mode = basicvirtual rss_glb_config_options = tnlmapen,hashtoeplitz,tnlalllkp # The following Scatter Gather Engine (SGE) settings assume a 4KB Host # Page Size and a 64B L1 Cache Line Size. It programs the # EgrStatusPageSize and IngPadBoundary to 64B and the PktShift to 2. # If a Master PF Driver finds itself on a machine with different # parameters, then the Master PF Driver is responsible for initializing # these parameters to appropriate values. # # Notes: # 1. The Free List Buffer Sizes below are raw and the firmware will # round them up to the Ingress Padding Boundary. # 2. The SGE Timer Values below are expressed below in microseconds. # The firmware will convert these values to Core Clock Ticks when # it processes the configuration parameters. # reg[0x1008] = 0x40810/0x21c70 # SGE_CONTROL reg[0x100c] = 0x22222222 # SGE_HOST_PAGE_SIZE reg[0x10a0] = 0x01040810 # SGE_INGRESS_RX_THRESHOLD reg[0x1044] = 4096 # SGE_FL_BUFFER_SIZE0 reg[0x1048] = 65536 # SGE_FL_BUFFER_SIZE1 reg[0x104c] = 1536 # SGE_FL_BUFFER_SIZE2 reg[0x1050] = 9024 # SGE_FL_BUFFER_SIZE3 reg[0x1054] = 9216 # SGE_FL_BUFFER_SIZE4 reg[0x1058] = 2048 # SGE_FL_BUFFER_SIZE5 reg[0x105c] = 128 # SGE_FL_BUFFER_SIZE6 reg[0x1060] = 8192 # SGE_FL_BUFFER_SIZE7 reg[0x1064] = 16384 # SGE_FL_BUFFER_SIZE8 reg[0x10a4] = 0xa000a000/0xf000f000 # SGE_DBFIFO_STATUS reg[0x10a8] = 0x2000/0x2000 # SGE_DOORBELL_CONTROL sge_timer_value = 5, 10, 20, 50, 100, 200 # SGE_TIMER_VALUE* in usecs # enable TP_OUT_CONFIG.IPIDSPLITMODE reg[0x7d04] = 0x00010000/0x00010000 # disable TP_PARA_REG3.RxFragEn reg[0x7d6c] = 0x00000000/0x00007000 reg[0x7dc0] = 0x0e2f8849 # TP_SHIFT_CNT # TP_VLAN_PRI_MAP to select filter tuples # filter tuples : fragmentation, mpshittype, macmatch, ethertype, # protocol, tos, vlan, vnic_id, port, fcoe # valid filterModes are described the Terminator 4 Data Book filterMode = fragmentation, mpshittype, protocol, vlan, port, fcoe # filter tuples enforced in LE active region (equal to or subset of filterMode) filterMask = protocol, fcoe # Percentage of dynamic memory (in either the EDRAM or external MEM) # to use for TP RX payload tp_pmrx = 34 # TP RX payload page size tp_pmrx_pagesize = 64K # TP number of RX channels tp_nrxch = 0 # 0 (auto) = 1 # Percentage of dynamic memory (in either the EDRAM or external MEM) # to use for TP TX payload tp_pmtx = 32 # TP TX payload page size tp_pmtx_pagesize = 64K # TP number of TX channels tp_ntxch = 0 # 0 (auto) = equal number of ports # TP OFLD MTUs tp_mtus = 88, 256, 512, 576, 808, 1024, 1280, 1488, 1500, 2002, 2048, 4096, 4352, 8192, 9000, 9600 # ULPRX iSCSI Page Sizes reg[0x19168] = 0x04020100 # 64K, 16K, 8K and 4K # Some "definitions" to make the rest of this a bit more readable. We support # 4 ports, 3 functions (NIC, FCoE and iSCSI), scaling up to 8 "CPU Queue Sets" # per function per port ... # # NMSIX = 1088 # available MSI-X Vectors # NVI = 128 # available Virtual Interfaces # NMPSTCAM = 336 # MPS TCAM entries # # NPORTS = 4 # ports # NCPUS = 8 # CPUs we want to support scalably # NFUNCS = 3 # functions per port (NIC, FCoE, iSCSI) # Breakdown of Virtual Interface/Queue/Interrupt resources for the "Unified # PF" which many OS Drivers will use to manage most or all functions. # # Each Ingress Queue can use one MSI-X interrupt but some Ingress Queues can # use Forwarded Interrupt Ingress Queues. For these latter, an Ingress Queue # would be created and the Queue ID of a Forwarded Interrupt Ingress Queue # will be specified as the "Ingress Queue Asynchronous Destination Index." # Thus, the number of MSI-X Vectors assigned to the Unified PF will be less # than or equal to the number of Ingress Queues ... # # NVI_NIC = 4 # NIC access to NPORTS # NFLIQ_NIC = 32 # NIC Ingress Queues with Free Lists # NETHCTRL_NIC = 32 # NIC Ethernet Control/TX Queues # NEQ_NIC = 64 # NIC Egress Queues (FL, ETHCTRL/TX) # NMPSTCAM_NIC = 16 # NIC MPS TCAM Entries (NPORTS*4) # NMSIX_NIC = 32 # NIC MSI-X Interrupt Vectors (FLIQ) # # NVI_OFLD = 0 # Offload uses NIC function to access ports # NFLIQ_OFLD = 16 # Offload Ingress Queues with Free Lists # NETHCTRL_OFLD = 0 # Offload Ethernet Control/TX Queues # NEQ_OFLD = 16 # Offload Egress Queues (FL) # NMPSTCAM_OFLD = 0 # Offload MPS TCAM Entries (uses NIC's) # NMSIX_OFLD = 16 # Offload MSI-X Interrupt Vectors (FLIQ) # # NVI_RDMA = 0 # RDMA uses NIC function to access ports # NFLIQ_RDMA = 4 # RDMA Ingress Queues with Free Lists # NETHCTRL_RDMA = 0 # RDMA Ethernet Control/TX Queues # NEQ_RDMA = 4 # RDMA Egress Queues (FL) # NMPSTCAM_RDMA = 0 # RDMA MPS TCAM Entries (uses NIC's) # NMSIX_RDMA = 4 # RDMA MSI-X Interrupt Vectors (FLIQ) # # NEQ_WD = 128 # Wire Direct TX Queues and FLs # NETHCTRL_WD = 64 # Wire Direct TX Queues # NFLIQ_WD = 64 ` # Wire Direct Ingress Queues with Free Lists # # NVI_ISCSI = 4 # ISCSI access to NPORTS # NFLIQ_ISCSI = 4 # ISCSI Ingress Queues with Free Lists # NETHCTRL_ISCSI = 0 # ISCSI Ethernet Control/TX Queues # NEQ_ISCSI = 4 # ISCSI Egress Queues (FL) # NMPSTCAM_ISCSI = 4 # ISCSI MPS TCAM Entries (NPORTS) # NMSIX_ISCSI = 4 # ISCSI MSI-X Interrupt Vectors (FLIQ) # # NVI_FCOE = 4 # FCOE access to NPORTS # NFLIQ_FCOE = 34 # FCOE Ingress Queues with Free Lists # NETHCTRL_FCOE = 32 # FCOE Ethernet Control/TX Queues # NEQ_FCOE = 66 # FCOE Egress Queues (FL) # NMPSTCAM_FCOE = 32 # FCOE MPS TCAM Entries (NPORTS) # NMSIX_FCOE = 34 # FCOE MSI-X Interrupt Vectors (FLIQ) # Two extra Ingress Queues per function for Firmware Events and Forwarded # Interrupts, and two extra interrupts per function for Firmware Events (or a # Forwarded Interrupt Queue) and General Interrupts per function. # # NFLIQ_EXTRA = 6 # "extra" Ingress Queues 2*NFUNCS (Firmware and # # Forwarded Interrupts # NMSIX_EXTRA = 6 # extra interrupts 2*NFUNCS (Firmware and # # General Interrupts # Microsoft HyperV resources. The HyperV Virtual Ingress Queues will have # their interrupts forwarded to another set of Forwarded Interrupt Queues. # # NVI_HYPERV = 16 # VMs we want to support # NVIIQ_HYPERV = 2 # Virtual Ingress Queues with Free Lists per VM # NFLIQ_HYPERV = 40 # VIQs + NCPUS Forwarded Interrupt Queues # NEQ_HYPERV = 32 # VIQs Free Lists # NMPSTCAM_HYPERV = 16 # MPS TCAM Entries (NVI_HYPERV) # NMSIX_HYPERV = 8 # NCPUS Forwarded Interrupt Queues # Adding all of the above Unified PF resource needs together: (NIC + OFLD + # RDMA + ISCSI + FCOE + EXTRA + HYPERV) # # NVI_UNIFIED = 28 # NFLIQ_UNIFIED = 106 # NETHCTRL_UNIFIED = 32 # NEQ_UNIFIED = 124 # NMPSTCAM_UNIFIED = 40 # # The sum of all the MSI-X resources above is 74 MSI-X Vectors but we'll round # that up to 128 to make sure the Unified PF doesn't run out of resources. # # NMSIX_UNIFIED = 128 # # The Storage PFs could need up to NPORTS*NCPUS + NMSIX_EXTRA MSI-X Vectors # which is 34 but they're probably safe with 32. # # NMSIX_STORAGE = 32 # Note: The UnifiedPF is PF4 which doesn't have any Virtual Functions # associated with it. Thus, the MSI-X Vector allocations we give to the # UnifiedPF aren't inherited by any Virtual Functions. As a result we can # provision many more Virtual Functions than we can if the UnifiedPF were # one of PF0-3. # # All of the below PCI-E parameters are actually stored in various *_init.txt # files. We include them below essentially as comments. # # For PF0-3 we assign 8 vectors each for NIC Ingress Queues of the associated # ports 0-3. # # For PF4, the Unified PF, we give it an MSI-X Table Size as outlined above. # # For PF5-6 we assign enough MSI-X Vectors to support FCoE and iSCSI # storage applications across all four possible ports. # # Additionally, since the UnifiedPF isn't one of the per-port Physical # Functions, we give the UnifiedPF and the PF0-3 Physical Functions # different PCI Device IDs which will allow Unified and Per-Port Drivers # to directly select the type of Physical Function to which they wish to be # attached. # # Note that the actual values used for the PCI-E Intelectual Property will be # 1 less than those below since that's the way it "counts" things. For # readability, we use the number we actually mean ... # # PF0_INT = 8 # NCPUS # PF1_INT = 8 # NCPUS # PF2_INT = 8 # NCPUS # PF3_INT = 8 # NCPUS # PF0_3_INT = 32 # PF0_INT + PF1_INT + PF2_INT + PF3_INT # # PF4_INT = 128 # NMSIX_UNIFIED # PF5_INT = 32 # NMSIX_STORAGE # PF6_INT = 32 # NMSIX_STORAGE # PF7_INT = 0 # Nothing Assigned # PF4_7_INT = 192 # PF4_INT + PF5_INT + PF6_INT + PF7_INT # # PF0_7_INT = 224 # PF0_3_INT + PF4_7_INT # # With the above we can get 17 VFs/PF0-3 (limited by 336 MPS TCAM entries) # but we'll lower that to 16 to make our total 64 and a nice power of 2 ... # # NVF = 16 # For those OSes which manage different ports on different PFs, we need # only enough resources to support a single port's NIC application functions # on PF0-3. The below assumes that we're only doing NIC with NCPUS "Queue # Sets" for ports 0-3. The FCoE and iSCSI functions for such OSes will be # managed on the "storage PFs" (see below). # [function "0"] nvf = 16 # NVF on this function wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 1 # 1 port niqflint = 8 # NCPUS "Queue Sets" nethctrl = 8 # NCPUS "Queue Sets" neq = 16 # niqflint + nethctrl Egress Queues nexactf = 8 # number of exact MPSTCAM MAC filters cmask = all # access to all channels pmask = 0x1 # access to only one port [function "1"] nvf = 16 # NVF on this function wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 1 # 1 port niqflint = 8 # NCPUS "Queue Sets" nethctrl = 8 # NCPUS "Queue Sets" neq = 16 # niqflint + nethctrl Egress Queues nexactf = 8 # number of exact MPSTCAM MAC filters cmask = all # access to all channels pmask = 0x2 # access to only one port [function "2"] nvf = 16 # NVF on this function wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 1 # 1 port niqflint = 8 # NCPUS "Queue Sets" nethctrl = 8 # NCPUS "Queue Sets" neq = 16 # niqflint + nethctrl Egress Queues nexactf = 8 # number of exact MPSTCAM MAC filters cmask = all # access to all channels pmask = 0x4 # access to only one port [function "3"] nvf = 16 # NVF on this function wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 1 # 1 port niqflint = 8 # NCPUS "Queue Sets" nethctrl = 8 # NCPUS "Queue Sets" neq = 16 # niqflint + nethctrl Egress Queues nexactf = 8 # number of exact MPSTCAM MAC filters cmask = all # access to all channels pmask = 0x8 # access to only one port # Some OS Drivers manage all application functions for all ports via PF4. # Thus we need to provide a large number of resources here. For Egress # Queues we need to account for both TX Queues as well as Free List Queues # (because the host is responsible for producing Free List Buffers for the # hardware to consume). # [function "4"] wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 28 # NVI_UNIFIED niqflint = 170 # NFLIQ_UNIFIED + NLFIQ_WD nethctrl = 100 # NETHCTRL_UNIFIED + NETHCTRL_WD neq = 256 # NEQ_UNIFIED + NEQ_WD nexactf = 40 # NMPSTCAM_UNIFIED cmask = all # access to all channels pmask = all # access to all four ports ... nethofld = 1024 # number of user mode ethernet flow contexts nroute = 32 # number of routing region entries nclip = 32 # number of clip region entries nfilter = 496 # number of filter region entries nserver = 496 # number of server region entries nhash = 12288 # number of hash region entries protocol = nic_vm, ofld, rddp, rdmac, iscsi_initiator_pdu, iscsi_target_pdu tp_l2t = 3072 tp_ddp = 3 tp_ddp_iscsi = 2 tp_stag = 3 tp_pbl = 10 tp_rq = 13 # We have FCoE and iSCSI storage functions on PF5 and PF6 each of which may # need to have Virtual Interfaces on each of the four ports with up to NCPUS # "Queue Sets" each. # [function "5"] wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 4 # NPORTS niqflint = 34 # NPORTS*NCPUS + NMSIX_EXTRA nethctrl = 32 # NPORTS*NCPUS neq = 64 # NPORTS*NCPUS * 2 (FL, ETHCTRL/TX) nexactf = 4 # NPORTS cmask = all # access to all channels pmask = all # access to all four ports ... nserver = 16 nhash = 2048 tp_l2t = 1020 protocol = iscsi_initiator_fofld tp_ddp_iscsi = 2 iscsi_ntask = 2048 iscsi_nsess = 2048 iscsi_nconn_per_session = 1 iscsi_ninitiator_instance = 64 [function "6"] wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 4 # NPORTS niqflint = 34 # NPORTS*NCPUS + NMSIX_EXTRA nethctrl = 32 # NPORTS*NCPUS neq = 66 # NPORTS*NCPUS * 2 (FL, ETHCTRL/TX) + 2 (EXTRA) nexactf = 32 # NPORTS + adding 28 exact entries for FCoE # which is OK since < MIN(SUM PF0..3, PF4) # and we never load PF0..3 and PF4 concurrently cmask = all # access to all channels pmask = all # access to all four ports ... nhash = 2048 tp_l2t = 4 protocol = fcoe_initiator tp_ddp = 1 fcoe_nfcf = 16 fcoe_nvnp = 32 fcoe_nssn = 1024 # The following function, 1023, is not an actual PCIE function but is used to # configure and reserve firmware internal resources that come from the global # resource pool. # [function "1023"] wx_caps = all # write/execute permissions for all commands r_caps = all # read permissions for all commands nvi = 4 # NVI_UNIFIED cmask = all # access to all channels pmask = all # access to all four ports ... nexactf = 8 # NPORTS + DCBX + nfilter = 16 # number of filter region entries # For Virtual functions, we only allow NIC functionality and we only allow # access to one port (1 << PF). Note that because of limitations in the # Scatter Gather Engine (SGE) hardware which checks writes to VF KDOORBELL # and GTS registers, the number of Ingress and Egress Queues must be a power # of 2. # [function "0/*"] # NVF wx_caps = 0x82 # DMAQ | VF r_caps = 0x86 # DMAQ | VF | PORT nvi = 1 # 1 port niqflint = 4 # 2 "Queue Sets" + NXIQ nethctrl = 2 # 2 "Queue Sets" neq = 4 # 2 "Queue Sets" * 2 nexactf = 4 cmask = all # access to all channels pmask = 0x1 # access to only one port ... [function "1/*"] # NVF wx_caps = 0x82 # DMAQ | VF r_caps = 0x86 # DMAQ | VF | PORT nvi = 1 # 1 port niqflint = 4 # 2 "Queue Sets" + NXIQ nethctrl = 2 # 2 "Queue Sets" neq = 4 # 2 "Queue Sets" * 2 nexactf = 4 cmask = all # access to all channels pmask = 0x2 # access to only one port ... [function "2/*"] # NVF wx_caps = 0x82 # DMAQ | VF r_caps = 0x86 # DMAQ | VF | PORT nvi = 1 # 1 port niqflint = 4 # 2 "Queue Sets" + NXIQ nethctrl = 2 # 2 "Queue Sets" neq = 4 # 2 "Queue Sets" * 2 nexactf = 4 cmask = all # access to all channels pmask = 0x4 # access to only one port ... [function "3/*"] # NVF wx_caps = 0x82 # DMAQ | VF r_caps = 0x86 # DMAQ | VF | PORT nvi = 1 # 1 port niqflint = 4 # 2 "Queue Sets" + NXIQ nethctrl = 2 # 2 "Queue Sets" neq = 4 # 2 "Queue Sets" * 2 nexactf = 4 cmask = all # access to all channels pmask = 0x8 # access to only one port ... # MPS features a 196608 bytes ingress buffer that is used for ingress buffering # for packets from the wire as well as the loopback path of the L2 switch. The # folling params control how the buffer memory is distributed and the L2 flow # control settings: # # bg_mem: %-age of mem to use for port/buffer group # lpbk_mem: %-age of port/bg mem to use for loopback # hwm: high watermark; bytes available when starting to send pause # frames (in units of 0.1 MTU) # lwm: low watermark; bytes remaining when sending 'unpause' frame # (in inuits of 0.1 MTU) # dwm: minimum delta between high and low watermark (in units of 100 # Bytes) # # [port "0"] dcb = ppp, dcbx # configure for DCB PPP and enable DCBX offload bg_mem = 25 lpbk_mem = 25 hwm = 30 lwm = 15 dwm = 30 dcb_app_tlv[0] = 0x8906, ethertype, 3 dcb_app_tlv[1] = 0x8914, ethertype, 3 dcb_app_tlv[2] = 3260, socketnum, 5 [port "1"] dcb = ppp, dcbx bg_mem = 25 lpbk_mem = 25 hwm = 30 lwm = 15 dwm = 30 dcb_app_tlv[0] = 0x8906, ethertype, 3 dcb_app_tlv[1] = 0x8914, ethertype, 3 dcb_app_tlv[2] = 3260, socketnum, 5 [port "2"] dcb = ppp, dcbx bg_mem = 25 lpbk_mem = 25 hwm = 30 lwm = 15 dwm = 30 dcb_app_tlv[0] = 0x8906, ethertype, 3 dcb_app_tlv[1] = 0x8914, ethertype, 3 dcb_app_tlv[2] = 3260, socketnum, 5 [port "3"] dcb = ppp, dcbx bg_mem = 25 lpbk_mem = 25 hwm = 30 lwm = 15 dwm = 30 dcb_app_tlv[0] = 0x8906, ethertype, 3 dcb_app_tlv[1] = 0x8914, ethertype, 3 dcb_app_tlv[2] = 3260, socketnum, 5 [fini] version = 0x1425001c checksum = 0x5ceab41e # Total resources used by above allocations: # Virtual Interfaces: 104 # Ingress Queues/w Free Lists and Interrupts: 526 # Egress Queues: 702 # MPS TCAM Entries: 336 # MSI-X Vectors: 736 # Virtual Functions: 64